What should I look for in a mixer tap?

Blog

1. Finish. Your tap’s finish should depend on the style of your kitchen, and tie in with hardware and appliances. …
2. Function. A tap is so much more than just water. …
3. Ergonomics. Opting for a mixer tap can have a number of benefits, including ease of use and temperature management. …
4. Shape. …
5. Mounting.

Besides, Are all mixer tap fittings the same?

Not all taps and countertop basins will be the same size, so you’ll want to make sure that there is adequate space from the top of your countertop basin to where the spout exits on the tap.

Keeping this in mind, Are mixer taps better than single taps? With two separate taps, you are limited to two flows of water—hot and cold. … With a mixer tap, you can set the temperature as it flows from the taps. This makes it far easier to precisely control the temperature of your water, whether you are running a bath, washing or shaving with water as it emerges from the tap.

What is a swivel mixer tap?

It means that the spout part of the kitchen sink mixer, where the water comes out of, can swivel on its base, this is so that you can turn the tap so that the water can be delivered to different areas or sides of your Kitchen Sink, for more kitchen sinks online have a look at our selection.

Are tap fittings universal?

There is no universal standard for which water supply goes on which side of the unit; however by almost universal practice in the UK: In the North, the hot water goes to the tap on the right of the unit while in the South, it goes on the left.

Do you need a plumber to install a mixer tap?

Always use a plumber to install your mixer tap.

By law, if you don’t have a plumbing license, you can not install or adjust your cold or hot water pipes. When a tap mixer is installed, the hot and cold water flexes are classed as water pipes.

What size is a standard tap fitting?

Tap backnuts typically measure either 27mm or 32mm AF (across flats), though they are more often described as being either 1/2 inch or 3/4 inch. The imperial measurements used to refer to the internal diameter of the threaded pipe they attach to, though this is no longer the case.

Are mixer taps more expensive?

The key factor is – according to the features that are available in a particular mixer tap, the price may vary, so if it has more features, it would cost more. A product made of superior quality normally would cost more.

What is the difference between a mixer tap and a monobloc tap?

Monobloc mixer taps

Some mixer taps come in a style that is known as a monobloc. Basically, this is a single built-up unit containing one or 2 tap handles and the spout. They’re suitable for deck mounted taps on baths or basins that have a single hole for the taps. They can also be used with countertop basins.

Are single-lever taps better?

Lower water consumption

Single-lever mixers use much less water compared to two-handle mixer taps. As it takes less time to set the temperature, less unused water ends up flowing straight down the drain with a single-lever mixer tap. This is good news for the environment – and your water bill!

What are the different types of taps?

Tapping tools are divided into four types: straight flute tap, spiral point tap, spiral fuse tap, and forming tap. Which type you use depends on what type of hole you want to thread, blind hole or through hole, and the component material.

What is a gooseneck tap?

Gooseneck taps, as the name suggests, have a gooseneck design for the main body of the tap. The high clearance that you get with a gooseneck tap makes it easier to clean larger items and fill up pots and large water bottles. The gooseneck design is quite modern and compliments double-bowl sinks best.

Do gooseneck taps swivel?

360° swivel spout. Wide flat surfaces beautifully designed to complement modern trend. Watermark and WELS Approved.

Are tap holes a standard size?

Standard taps and spouts generally require a hole of at least 22mm in diameter. … Sensor taps usually specify a 28mm diameter hole, although 25mm may be sufficient. Monobloc mixer taps, taking both a hot and cold supply, mostly require a minimum 32mm diameter hole.

What size are tap connectors?

The flexible pipes as a standard come with a 9-9.5mm inside diameter, although large bore tap connectors can be purchased with a 12-12.5mm inside diameter, increasing the water flow rate, used where there is a low water pressure and water flow rate is a problem for the tap or appliance.

What is the standard tap size in Australia?

A standard 15mm garden tap has a 15mm BSP Male threaded inlet and 20mm BSP Male threaded outlet. A 20mm garden tap has a 20mm BSP Male threaded inlet and 25mm BSP Male threaded outlet.

Can you install a mixer tap yourself?

“It’s a pretty simple process to change both. However, you need to take into account that your sink doesn’t already have a mixer tap I’m assuming it has a separate hot and cold. … I would suggest you buy a pair of flexible tap connector to make the installation easier.

Can I replace a mixer tap myself?

Replacing a kitchen tap is a fairly simple job to complete – you just need to have patience, a manual, and the right tools. Make sure you are extra careful when tightening, well, anything – over-tightening a single nut can lead to damage.

Can I install my own taps?

This is a job you can do yourself, but just how do you fit new taps? This is one of those tasks which shouldn’t be too difficult or too expensive. Fitting new bathroom taps should be a straightforward enough project to take on yourself, so long as you use common sense and follow simple instructions.

Are UK taps standard sizes?

Most taps in the UK are said to be a standard size, but it’s worth remembering that the size refers to the way in which the tap fits onto the pipes rather than the size of the taps themselves (basin taps being 1/2″ and bath taps having 3/4″ threads).

Is 3/4 the same as 22mm?

19mm = 3/4 inch. … 22mm = almost 7/8 inch. 23mm = 29/32 inch.

What size thread are kitchen taps?

Measuring BSP Sizes

Are more expensive taps better?

More expensive high-end taps are available in a much larger range of finishes, including rose gold, unlacquered brass, brushed bronze and copper, all finishes that get better with age, not worse. It’s your decision, but a designer tap is a much better long term investment than a cheaper and lower quality option.

How long do mixer taps last?

Mixer taps generally last for 5-10 years and they only have a 1 year warranty. So if the tap is over 1 year old, expect to replace it for a new one.