This could be caused by a virus, a corrupted OS, an improper shutdown, or the deletion of an important folder. On the other hand, physical crashes are caused by physical damage to the actual components of the hard drive. Likely causes could be accidental spills, drops, power surges, or plain old wear and tear.

Also How do I fix my Seagate external hard drive not responding?


Basic hardware troubleshooting steps:

  1. Try connecting the drive to a different port on the computer.
  2. If possible, try using a different cable.
  3. Try using the drive on a different computer.
  4. Verify the drive light is on. …
  5. Try a different power outlet.

Subsequently, What would cause a hard drive to stop working? There are a number of causes for hard drives to fail including: human error, hardware failure, firmware corruption, heat, water damage, power issues and mishaps. … Drives typically fail within a short time if there is a defect present from manufacturing.

Why is my Seagate external hard drive not being recognized? If your Seagate external hard drive is detected, the original cable is the cause. If the problem still appears, connect the external hard drive to another USB port. … If your computer is desktop, you should make sure that the USB port into which the Seagate external hard drive plugs is on the back of your computer.

Why is my Seagate hard drive not working?

A reason why your Seagate portable drive is not being recognized could be that you might have plugged it into a faulty or loose USB port. … Your Seagate portable drive may not be showing up because of a faulty USB cable as well; so you can replace the USB cable if changing the port doesn’t work.

How do I fix a corrupted Seagate hard drive?


To get to First Aid:

  1. Click on the partition to select it. When done correctly, the partition will be highlighted in blue (may vary at some point).
  2. Click on the First Aid tab.
  3. Click on “Verify Disk” and if Disk Utility says it’s needed, then run “Repair Disk”.

What do you do when your hard drive stops working?


What to Do When Your External Hard Drive Won’t Show Up

  1. Make Sure It’s Plugged In and Powered On. Western Digital My Book. …
  2. Try Another USB Port (or Another PC) …
  3. Update Your Drivers. …
  4. Enable and Format the Drive in Disk Management. …
  5. Clean the Disk and Start From Scratch. …
  6. Remove and Test the Bare Drive.

How do I fix my hard drive not working?


You can follow these steps to fix the problem with your hard drive.

  1. Inspect Hard Drive. Carefully inspect your hard disk for any physical damage. …
  2. Run CHKDSK. …
  3. Use an Antivirus & Anti-Malware Tool. …
  4. Re-Install the Drivers. …
  5. Format the Disk.

What do I do if my hard drive is not working?

Power down the computer. Install the drive physically into the computer. Boot up the computer.

…


Remove any potential conflicts:

  1. Power down the computer.
  2. Disconnect all other storage devices, external hard drives, thumb drives, printers, and cameras.
  3. Power the computer up again and retry detection.

How recover data from Seagate internal hard disk which is not detecting?


To check to see if this is the cause of the BIOS not detecting the hard drive, follow these steps:

  1. Power off the computer.
  2. Open the computer case and remove the data cable from the hard drive. This will stop any power saving commands from being sent.
  3. Turn on the system. Check to see if the hard drive is spinning.

How do I reset my Seagate external hard drive?


Reset using the button

  1. Power down the Seagate Central by unplugging it from power.
  2. Wait approximately 15 seconds.
  3. Power up the Seagate Central again.
  4. Wait for the device to fully boot and show a steady, non-blinking green light. This takes about three to four minutes. …
  5. Wait until the light becomes solidly illuminated.

How do I fix a hard drive that is not detected?

Unplug the hard drive which fails to be recognized by Windows BIOS, and remove the ATA or SATA cable and its power cable. If the ATA or SATA cable and the power cable are broken, change to a new one. If the cables are covered by dust, clear the dust.

What do I do if my hard drive is not detected?


To check to see if this is the cause of the BIOS not detecting the hard drive, follow these steps:

  1. Power off the computer.
  2. Open the computer case and remove the data cable from the hard drive. This will stop any power saving commands from being sent.
  3. Turn on the system. Check to see if the hard drive is spinning.

How do I reset my Seagate hard drive?


Reset using the button

  1. Power down the Seagate Central by unplugging it from power.
  2. Wait approximately 15 seconds.
  3. Power up the Seagate Central again.
  4. Wait for the device to fully boot and show a steady, non-blinking green light. This takes about three to four minutes. …
  5. Wait until the light becomes solidly illuminated.

How do you recover a corrupted hard drive?


Steps to Recover Data from a Corrupted or Crashed Hard Drive

  1. Download and Install Disk Drill for Windows or Mac OS X.
  2. Launch Disk Drill recovery software, select the crashed hard disk and click: …
  3. Preview the files you found with Quick or Deep Scan. …
  4. Click Recover button to recover your lost data.

How do I fix a corrupted hard drive?


Methods to Fix Corrupted Hard Drive

  1. Go to Computer/This PC >> Select Hard Drive >> Choose Properties.
  2. Select Tools >> Error checking >> Check now >> Check local disk >> Start.
  3. Shut down all open and running programs >> wait for the system to check upon the next boot >> restart the PC.

How do you recover data from internal HDD which is not detecting?


How to Recover Data from Hard Disk Which Is Not Detecting FAQs

  1. Launch EaseUS Data Recovery software on your computer, select the internal hard drive or external hard disk to get started.
  2. The hard drive recovery will start scanning the disk to searching your lost data and files.

How can I recover data from undetected internal hard disk?


Recover Data from Unbootable, Undetected Hard Drive in Advance

  1. Create a bootable disk. Prepare an empty USB. …
  2. Boot from the bootable USB. Connect the bootable disk to PC that won’t boot and change your computer boot sequence in BIOS. …
  3. Recover files/data from a PC/laptop hard drive that won’t boot.

What do I do if my hard drive is not detected?


What to Do When Your External Hard Drive Won’t Show Up

  1. Make Sure It’s Plugged In and Powered On. Western Digital My Book. …
  2. Try Another USB Port (or Another PC) …
  3. Update Your Drivers. …
  4. Enable and Format the Drive in Disk Management. …
  5. Clean the Disk and Start From Scratch. …
  6. Remove and Test the Bare Drive.

How do I factory reset my Seagate external hard drive Windows 10?


Reset using the Seagate Central Assistant

  1. Log in with your credentials.
  2. Select the Settings tab.
  3. Select the Restore button. This will restore the device settings to default values.
  4. Proceed with initial setup.

How do I reset my external hard drive to factory settings?

Click the Go menu, select Utilities from the drop-down menu, and open Disk Utility. Choose your external drive from the left sidebar, and click Erase. Give your drive a name and select the file system you want from the Format drop-down. Click Erase, and the system will reformat your drive.

How do I reset my Seagate external hard drive Windows 10?

Click “Disk Management,” then locate your Seagate external hard drive. Right-click the drive and click “Format.” Click “OK,” if you want to reset the drive using the existing settings; you can choose to change the name of the drive.

How do I fix Windows 10 not detecting my hard drive?


How to fix “Hard drive not detected” on Windows 10?

  1. Re-enable the missing drive in the Disk Management.
  2. Reconnect the external hard drive.
  3. Format the drive.
  4. Check the status of the hard drive.
  5. Update the driver.
  6. Update Windows.
  7. Reinstall USB controllers to make the second hard drive recognized.

How do I fix my external hard drive not detected Windows 10?


Fixing driver issues

  1. Open Start.
  2. Search for Device Manager and click the top result to open the experience.
  3. Expand the Disk drives branch.
  4. Right-click the external drive with the problem and click the Update driver option.
  5. Click the Search automatically for updated driver software option.

General, knowledge