If the spindle looks bent or broken, then it needs to be replaced. You will feel how the blades start to move unevenly and cut your grass in a disorganized way. In some cases, the blade won’t spin at all or instead make loud cracking noises. Either way, it means your spindle needs some replacement.
Subsequently, How do you remove a spindle pulley?
Also, How do you remove the crankshaft pulley on a riding lawn mower?
How do you remove the crankshaft pulley on a riding lawn mower? Unscrew the pulley removal tool’s center bolt until the bolt bottoms out against the pulley removal tool. Set the pulley removal tool onto the lawnmower pulley, aligning the pulley removal tool’s center bolt with the pulley shaft.
How often should you grease mower spindles?
The spindles and caster wheels are generally the most often greased. The spindles and castor wheels should be done around once a month because of the moving interior parts. Commercial mowers that put hundreds of hours on their Ferris mower would be looking at greasing the mower everyday depending on usage.
Last Review : 5 days ago.
How do you remove a crankshaft pulley from a lawn tractor?
How long do mower spindles last?
about 2-3 years
How do I know if my mower deck spindle is bad?
Bent & Broken Parts If the spindle looks bent or broken, then it needs to be replaced. You will feel how the blades start to move unevenly and cut your grass in a disorganized way. In some cases, the blade won’t spin at all or instead make loud cracking noises. Either way, it means your spindle needs some replacement.
How do I know if my spindle bearings are bad?
put a streight round bar in a tool holder and put it in the spindle. Then put a . 0001 indicator on the round bar and push the bar with your hand. If you can deflect the spindle more then a tenth or two with your hand you have a bearing problem.
How do you remove crankshaft pulley?
– Position the puller in front of the pulley. …
– Install the puller-to-pulley bolts. …
– Using a breaker bar and socket, tighten the central puller bolt until the pulley slides off the crankshaft. …
– For installation, ensure that the crankshaft, pulley bore and keyways are clean and free of any debris or corrosion.
How do you know if a spindle is bad?
– Finish Issues. One sign that your spindle is about to need repairs is if you notice finish issues on machined products. …
– Spindle Mouth Wear. If you notice wear at the spindle mouth, it is a good sign that you need to invest in repairs. …
– Fretting in Toolholders. …
– Vibration. …
– Noise. …
– Temperature.
How do you remove a pulley from a deck spindle?
Take two bolts and thread them in the two smaller holes. Tighen the bolts slowly and evenly and the pulley will drop down. Then take a small chisel and open up the vertical line in the hub. You may need to use a puller to get the hub off of the shaft, but it will come.
How do you get a stuck pulley off a riding lawn mower?
Spray a liberal amount of penetrating oil onto the front and back sides of the pulley hub until they are thoroughly soaked. Spray the pulley retaining bolt and pulley shaft with the oil. Allow about 30 minutes to two hours for the penetrating oil to loosen the rusted pulley and other parts.
Can you over grease mower spindles?
“GREASING MOWER SPINDLES” “Grease fittings on mower spindles are used for assembly only. DO NOT grease spindles or damage may occur to bearing seals”.
How do you change a spindle on a zero turn mower?
How do you remove the pulley from a spindle?
What does a bad spindle sound like?
Squealing. In riding mowers, the spindle tends to be a little larger than most mowers. This causes it to make loud squealing sounds when it goes bad. There’s a chance the spindle is broken, or the bearings are worn out.
Can you drive with a bad spindle?
Driving with a bad wheel bearing can cause the axle/hub/spindle to weld itself from friction and heat causing the wheel to lock up and spin you out. More likely, the metal will wear away from the friction and the wheel/hub will become loose.
How do you remove a crankshaft pulley without a puller?
There is a way to do it. You put a wrench on the pulley bolt and block the other end against the floor or the frame. Then you use the starter motor to turn the engine (DO NOT START IT, JUST TURN IT) for at most one or two revolutions of the crank. Just enough to break the bolt loose.
How do you remove a pulley from a spindle?
Take two bolts and thread them in the two smaller holes. Tighen the bolts slowly and evenly and the pulley will drop down. Then take a small chisel and open up the vertical line in the hub. You may need to use a puller to get the hub off of the shaft, but it will come.
[advanced_iframe use_shortcode_attributes_only=”true” src=”about:blank” height=”800″ width=”800″ change_parent_links_target=”a#link1″ show_iframe_as_layer=”external” enable_ios_mobile_scolling=”true”]
Spread the word ! Don’t forget to share.