Pedals that amplify or add noise should go near the beginning of the signal path. This includes overdrive/distortion effects, compressors, and wah pedals. If they’re later in the signal path, they will amplify the noise of everything before them, which can be difficult to control.

Besides, How do you stack overdrive and distortion?


Tips For Stacking Overdrive and Distortion Pedals

  1. When stacking 2 dirt pedals together, the second pedal in the chain dictates the overall tone of the stack. …
  2. Cranking the volume on the first pedal in the stack will not raise the volume, but will increase the clipping (gain) in the second pedal.

Keeping this in mind, What order do effects pedals go in? Conventional wisdom suggests that the ideal pedal order is wah/filter, compression, overdrive, modulation and pitch-based effects, delay, and reverb.

Where does Tube Screamer go in effects chain?

Tube screamers work best at the start or middle of the pedal chain. Tube screamer pedals are a type of overdrive pedal. They are best known for creating a crunchy and saturated tone by adding gain, and increasing the mid-range and treble-frequencies and lowering the bass-frequencies.

What order should your pedals be in?

Dynamics (compressors), filters (wah), pitch shifters, and Volume pedals typically go at the beginning of the signal chain. Gain based effects such as and overdrive/distortion pedals come next. Modulation effects such as chorus, flangers, phasers typically come next in the chain.

How do I use multiple overdrive pedals?

To give yourself a different set of sounds, start with a pedal that has the tonal characteristics of a specific amp, ideally one that is different from your amp. Then stack that pedal with another gain flavor, and you have two distinct amp tones that can both be overdriven.

Does Wah go before or after compressor?

In a pedalboard, the compressor unit generally goes after a wah pedal. While it is of course a matter of preference, putting the compressor first will limit the range, function, and dynamics of the wah pedal. The result will be arguably less musical and pleasing overall.

Does pedal order matter?

The order of your pedals matter

The order in which the pedals are set up matter because the signal is being processed multiple times if you have multiple pedals. A general rule of thumb is to first set your distortion and drive pedals first, followed by your modulation pedals like echo, chorus, flanger, tremolo, etc.

Can you use two guitar pedals at once?

The only extra thing you need to be able to connect more than one pedal, is a patch cable. They’re small cables that are designed to connect your guitar pedals to one another. Then you connect the first pedal to your guitar as normal, and your last pedal to your amp. Then you form a pedal chain.

Where should the wah pedal go?

Dynamics (compressors), filters (wah), pitch shifters, and Volume pedals typically go at the beginning of the signal chain. Gain based effects such as and overdrive/distortion pedals come next. Modulation effects such as chorus, flangers, phasers typically come next in the chain.

Which comes first Noise Gate or compressor?

This is why most guitarists place the compressor first, in order to send a stronger, better signal to the other effects. … Sometimes you can remedy this by placing a noise gate before the compressor, however, the noise reduction can have an effect on the tone quality.

Can I put wah before tuner?

I usually put it after my tuner (which is true bypass), after my wah pedal (which likes to be early in the chain), and before overdrives and fuzzes. … If I am using my Boss TU3 tuner, which has a buffer, I like it after the wah. The wah I have does not like buffers in front.

Should chorus go before or after delay?

Chorus is a modulation effect, and as such, it should be placed fairly late in your pedal chain. It should come after a wah pedal, compression pedal, overdrive pedal, and distortion pedal, but before your delay pedal, tremolo pedal, or reverb pedal.

Does reverb go before or after delay?

In a guitar signal chain, the delay unit is generally placed before a reverb pedal, but it’s up to the individual musician to decide on the order. Putting delay before reverb can muddy up the sound, so most guitarists prefer placing it after the delay.

How do you hit multiple guitar pedals at once?

Switch between FX chains

Set up both of those sounds, each using a completely different set of pedals. They could even each go to separate amps, if you like. Connect the guitar to both of these chains through an A/B switch pedal. Now, at the tap of a footswitch, you can switch from one set of pedals to another.

Do I need a loop switcher?

A loop switcher will make my rig more reliable by allowing me to “remove” failing pedals and cables from my signal flow. If a cable shorts or pedal smokes, the damage can be excised with a bypassed loop. If you have pedals that are prone to misbehaving, a true-bypass loop switcher can remove them instantly.

Where do you put a clean boost pedal?

Some people like to place the clean boost right at the beginning, while others prefer to place it after their overdrives and distortion pedals. If you have your clean boost right at the beginning of your chain, turning it on when you have an overdrive or distortion activated will cause your tone to get grittier.

Where do you place a volume pedal?

The volume pedal should be placed after the overdrive/distortion section but before the time-based effects (reverb and delay) within the effects chain. This allows for a ‘long trail’ essential for the delay and reverb to continue ‘sustaining’ the sound when the volume pedal is cut off.

Can you use a noise gate and compressor?

Putting a noise gate after the compressor will clean up the hiss but it will not remove mistakes that your playing is introducing. It will also clamp some of the notes, and depending on your settings and the quality of the gate this can mess with your tone.

Where should noise gate go in pedal chain?

Where does a noise gate go in your signal chain? In some ways, this is subjective. Naturally, you’ll want to place the noise gate wherever the noise is, for example after your fuzz pedal. It’s most common, however, to put it at the end of your chain but before any ambient pedals such as delay and reverb.

Where should a compressor go in a signal chain?

Place your compressor in front of your overdrive pedal in the signal chain. To get a super-smooth, low-gain lead sound, reverse the order of the pedals in the signal chain and use the same settings.

What goes first wah or tuner?

The tuner pedal should go first in the effect signal chain. This is to allow the cleanest signal into the pedal for viewing the most accurate tuning pitch. Positioning the tuner pedal after other effects (distortion, modulation, EQ pedals, etc) can distort the notes in the signal affecting pitch accuracy.

Where should I put my delay pedal?

Delays and reverbs

The end of the signal chain is where the delay/echo and reverb effects should be placed – preferably with the delay in front of reverb – primarily because both are “ambience” effects that give the illusion of a sonic space or atmosphere.

Can you use chorus with distortion?

Yes, the chorus pedal can be used to fatten and thicken up a distorted tone, but if you use a distortion heavy sound, the chorus will just muddy up your tone and you’ll get lost in the mix.